Volumetric Change and Surface Properties of Temperature-Sensitive Polyvinylalcohol (PVA) Hydrogel

Polyvinylalcohol (PVA) polymer gel is a temperature sensitive polymeric gel, with a critical transition temperature (with H₂O) of 310 K. At higher than 310 K, this temperature sensitive polymer gel shrinks because of discharging water, whereas at lower temperatures, the gel swelled because of absorbing water. The reversibility of the gel's volume change was confirmed by temperature swing. The adsorption behavior of an organic compound onto the PVA polymer gel in water was tested at various temperatures. The amount of adsorbed organic compound increased remarkably at temperatures higher than about 310 K. Then, it was confirmed that the organic compound in PVA polymer gel could be reversibly adsorbed and desorbed by a temperature change between 293 and 323 K. The mechanism of adsorption of the organic compound onto the PVA polymer gel could be explained by hydration and dehydration of polymer gel.     

掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

天然气吸附储存脱附过程的动态模拟

通过热动力学计算,认识了脱附过程当中储罐内温度剖面分布的典型特征:储罐轴心处的温度下降幅度最大。分析了脱附过程当中储罐壁的热交换、吸附剂的导热系数以及储罐内的初始压力对储罐内的温度剖面的影响。结论是加强储罐外壁的热交换、增大吸附剂的导热系数皆能改善吸附储罐内的温度剖面。     

低密度微泡沫压井液的研究与应用

吐哈油田部分区块地层压力系数小于0.9,常规水基压井液对储层伤害大,若使用油基压井液成本高,环境污染严重。通过实验优选出了一种低密度水基微泡沫压井液。该压井液具有密度低、泡沫强度高、稳定性好、携砂能力强等优点。现场应用表明,低密度微泡沫压井液稳定时间大于48 h,密度在0.70~0.99 g/cm3之间可调,抗油污染能力强,抗油大于8%,抗温在100℃以上,岩心污染后渗透率恢复值大于80%;并且施工方便,成本低,具有储层保护能力,使用微泡沫压井液的井表皮系数在0.20~2.34之间。     

300km/h高速铁路PC槽型梁动力试验研究

介绍北方交通大学与比利时鲁汶大学、布鲁塞尔自由大学、比利时铁路公司合作,在巴黎至布鲁塞尔之间高速铁路线上的Antoing大桥进行的二次高速铁路桥梁动力试验。试验桥梁由跨度50m的多跨预应力混凝土简支槽型梁构成,试验中列车速度达265-310km/h。通过现场试验和实验结果分析,得到了桥梁的频率、振型、阻尼等自振特性,以及桥梁在高速列车作用下的动挠度、梁和桥墩的横向和竖向加速度、橡胶支座的相对位移、梁体的动应变等动力响应特性。试验经验和测试结果对于充实高速铁路桥梁动力分析理论、改进数值分析模型、验证计算结果、提高高速铁路桥梁的动力设计水平、保证行车安全,具有重要的意义。     

Chemische Zusammensetzung und Mikrostruktur polymerabgeleiteter Gläser und Keramiken im System Si–C–O. Teil 2: Charakterisierung der Gefügeausbildung mittels hochauflösender Durchstrahlungselektronenmikroskopie und Feinbereichsbeugung

Chemical Composition and Microstructure of Polymer‐Derived Glasses and Ceramics in the Si–C–O System. Part 2: Characterization of microstructure formation by means of high‐resolution transmission electron microscopy and selected area diffraction Liquid or solid silicone resins represent the economically most interesting class of organic precursors for the pyrolytic production of glass and ceramics materials on silicon basis. As dense, dimensionally stable components can be cost‐effectively achieved by admixing reactive filler powders, chemical composition and microstructure development of the polymer‐derived residues must be exactly known during thermal decomposition. Thus, in the present work, glasses and ceramics produced by pyrolysis of the model precursor polymethylsiloxane at temperatures from 525 to 1550 °C are investigated. In part 1, by means of analytical electron microscopy, the bonding state of silicon was determined on a nanometre scale and the phase separation of the metastable Si–C–O matrix into SiO₂, C and SiC was proved. The in‐situ crystallization could be considerably accelerated by adding fine‐grained powder of inert fillers, such as Al₂O₃ or SiC, which permits effective process control. In part 2, the microstructure is characterized by high‐resolution transmission electron microscopy and selected area diffraction. Turbostratic carbon and cubic β‐SiC precipitate as crystallization products. Theses phases are embedded in an amorphous matrix. Inert fillers reduce the crystallization temperature by several hundred °C. In this case, the polymer‐derived Si–C–O material acts as a binding agent between the powder particles. Reaction layer formation does not occur. On the investigated pyrolysis conditions, no crystallization of SiO₂ was observed.     

滚动式冷床在高钢级油管生产线中的应用

根据石油开采业对石油机械产品的需求 ,利用机械理论基础知识 ,通过实践设计 ,提出了对几何尺寸长的金属管类进行调质处理后的均匀冷却方法 ,以满足其性能要求。     

低温高速离心泵的研制与应用

阐述了适合于输送低温介质的高速离心泵的水力设计和结构设计方法，结构上采有长，中，短叶片相间的复合叶轮及双密封结构，理论上采用以效率为目标函数的优化水力设计方法，保证了低温高速离心泵具有很好的工人可靠性和优越的性能指标。     

SJ—YⅡ—5型高爆速高威力水胶炸药的研制

文章简要分析了我国目前在中硬岩石爆破中工业炸药的使用情况，介绍了山西兴安化学材料厂新研制的一种适用于硬岩爆破的高爆速、高威力水胶炸药新品种，对其性能、爆破效果、经济实用性和安全性等进行了阐述。     

Effect of oxygen deficiency (δ) on transition temperature of yttrium cuprate superconductors

The nature of pairing mechanism as well as transition temperature of yttrium cuprates is discussed using the strong coupling theory. An interaction potential has been developed for the layered structure with two conducting CuO₂(a–b) layers in a unit cell. The interaction potential properly takes care of electron-electron, electron-phonon and electron-plasmon interactions. Furthermore, the electron-phonon coupling parameter (λ), the modified Coulomb repulsive parameter (μ*) and the 2D acoustic phonon (plasmon) energy as a function of oxygen deficiency is worked out. Finally, the superconducting transition temperature (T _c) is then evaluated by using these coupling parameters and obtainedT _c = 95(92)K for Y(Yb)Ba₂Cu₃O_7−δ superconductors withδ = 0·0. The model parameters estimated from the layered structure approach are consistent with the strong coupling theory. The result deduced on the variation ofT _c withδ are in fair agreement with the earlier reported data on yttrium cuprates. The analysis of the above results are discussed.